網帶式烘干機采用高溫抗拉鋼絲網帶，熱風加熱，均勻受熱，配有無極變速機，根據物料厚度和含水率調整進料進度，以達到理想的烘干效果。
1.工作原理
設備采用耐高溫抗拉鋼絲網帶在運行中上下兩層網帶同步運行，要烘干的物料在上下兩層網帶中間由上下網帶夾持運行進行烘干。
2.干燥系統
采用科學的烘干原理，用離心風機直接把熱風爐內的熱風注入機內的上下風箱中，熱風通過上下風箱的噴嘴吹到運行中單板的上下兩個網面，使單板受熱均勻，從而起到烘干的作用。
3.傳動系統
刨切單板由進料口送入機內，由上下網帶夾持相對運行，通過上下噴嘴以達到烘干效果。
4.控制系統
采用無極變速機根據您的單板厚度和含水率調整進料速度，以達到理想烘干效果。
5.加熱系統
可采用油加熱、電加熱、氣加熱、熱風加熱。
6.進料口寬度
1.35—3米可選擇。
7.干燥物料
單板：薄0.3毫米，厚4毫米。紙板及其它顆粒狀物料根據厚度及含水量確定烘干量。
中譯英：
Net belt type drying machine using high tensile steel wire mesh belt, hot air heating, uniform heating, with the promise speed machine, according to the material thickness and moisture adjustment feeding schedule, in order to achieve the ideal drying effect.
1 Working principle
Equipment with high temperature resistance and high tensile steel wire mesh belt in the operation of upper and lower two layers of mesh belt synchronous operation, to the dried material in upper and lower two layers of mesh belt intermediate composed of an upper and a lower mesh belt clamping operation of drying.
2 Drying system
The use of the scientific drying principle, using centrifugal fan directly to the hot blast furnace hot air injection machine within the upper and lower bellows, hot air through the upper and lower box nozzle to blow into the running board of two upper and lower net surface, so that the single plate is heated evenly, so as to achieve the effect of drying.
3 Transmission system
Sliced veneer from feed inlet into the machine, composed of an upper and a lower mesh belt clamping relative operation, through the upper and lower nozzle to achieve the effect of drying.
4 Control system
Uses the limitless speed machine based on your board thickness and moisture adjustment of feed rate, to achieve the ideal drying effect.
5 Heating system
The oil heating, electric heating, gas heating, hot air heating.
6 Inlet width
1.35 -3 meter selection.
7 Dry material
Veneer: the thin 0.3 mm, the thickness of 4mm. Cardboard and other granular materials according to the thickness and water content to determine the quantity of drying.
(圖/文http://m.jdfwb.com/)
加入收藏
